Today's industrial requirements have significantly improved, and thinner powder is conducive to the deep processing of the product, thus makes the product more value. Rotor Grinder for Potassium Fluoroborate can effectively improve the level of massage of materials and greatly improve productivity. Rotor Grinder for Potassium Fluoroborate has received much attention, and the prospect has also been optimistic about many people.
Rotor Grinder for Potassium Fluoroborate is mainly used for more refined materials. The pulverized particle diameter is 1.5 to 0.005 mm, and the crude material is sieved. The principle of pulverization is substantially the same as the hydraulic level, and the above settlement theory can also be used for airflow classification. However, in the airflow classification, since the density and viscosity of the air are much smaller than the density and viscosity of water, the same particles are more settle more in the air than in the water. Moreover, the density and viscosity of the air varies with temperature and pressure.
In order to cause air flow, wind pulverization equipment typically requires an appropriate fan (exhaust or blast).
When the airflow is classified, the fine particles are typically taken away by the airflow. In some cases, the raw material is sent to the gas stream into a pulverized device.
It is well known that the load of solid particles in air under normal pressure does not exceed 500 g / m3 air. When it reaches 1 kg / m3, the particles fall from the airflow. The load is related to the density and particle size of the particles. When the fine particle material is treated, the load generally does not exceed 200 to 300 g / 3 air. According to this calculation, the volume concentration of the solid in the gas stream is much smaller than 0.03. Therefore, when the airflow is classified, in most cases, it belongs to the free settlement.
The speed required to move the particulate material in the horizontal and vertical directions is relatively large, and the speed required in the horizontal direction is relatively large, and as the particle density increases, for example, for the density 1.5 of the pulverization coal per centimeter. The minimum wind speed is 2 m / sec; a powder material having a density of 2.5 g / cm, the speed is not less than 3.5 m / sec; a powder having a density of 4 g / cm 3, a minimum speed of 4 meters per second. Due to the complexity of the situation, the appropriate airflow rate in each particular situation should be determined by experiments.
In the rising airflow, the airflow speed required to suspend a certain density and particle size is greater than the calculated value of free settling, which is due to the uneven distribution of the airflow along the pulverizing chamber portion.
The Rotor Grinder for Potassium Fluoroborate has the characteristics of high pulverization, high pulverization efficiency, high pulverization precision, accurate cutting particle size, and good stability.
AlPotassium Sulfate Rotor Grinder for Potassium Fluoroborate Case Sharing: This customer is a Saudi company, which requires a grading of potassium sulfate super fine powder, and investigated many of the international powder equipment companies, and finally chose our AlPA classifier equipment.
Rotor Grinder for Potassium Fluoroborate material is not small, and the material is stacked in the silo plate knot, the material is marked, and the material has a bridge in the silo, the silo cone angle design There is no reason such as the rest of the material. Solving silo does not small materials suggests design phase to fully understand the properties of materials, such as pile specific gravity, liquidity, moisture resistance, rest horn, particle size, flammable and explosive properties. Using auxiliary measures, such as air disc, air hammer, air blowing, vibration discharge mechanism, artificial hitting, etc. The pulverizer is an apparatus for ultrafine pulverized dry materials with air separation, heavy polishing, and shear. It consists of a cylindrical crushed chamber, a polishing wheel, a polishing rail, a fan, a material collection system, and the like. The material enters the cylindrical pulverizing chamber through the feed port, and is crushed along the grinding rail, and the crush is achieved. The pulverized material passes out the pulverizer through the negative pressure air flow caused by the fan, and the material collection system is entered, filtered through the filter bag, the air is discharged, the material, the dust is collected, and the pulverization is completed.
Rotor Grinder for Potassium Fluoroborate's feeding system is one of the key components. It is often encountered in actual use. For example, the silo is not affected, and the feed is not uniform, and even can't feed. Simple analysis of non-uniform feeding of feed is more sticky or fluidity, and the design of the feeding system is designed. Feeding uneven resolution suggests based on material properties systemic solution, such as silo structure, auxiliary sheet structure, feeding valve structure, auxiliary feeding measures, and ventilation and control systems. The feeding system is generally silo, auxiliary tablet equipment, and feeding mechanism three components, depending on the material properties, the design parameters of the feeding system are different.
The above is the use of the use of the Rotor Grinder for Potassium Fluoroborate products and a simple solution. Everyone must pay more attention when using it.
Shan dong alpa produces various types of crushers, can be used in various materials such as medicinal materials, ingredients, chemicals in powder, and the highest effect can reach. Our products are non-standardized products, which will customize their products according to your needs, and make a reasonable offer according to the product.
